Parr-instrument PDM Bedienungsanleitung PDF herunterladen

Installation Instructions for

Pressure Display Module (PDM)

556M

Meter Installation in 4848 Reactor

Controller

1. Unplug the power cord of the 4848 controller.

Remove the (2) screws located on the top/front

cover at the rear corners of the controller. Gen-

tly lift the cover forward, which is hinged at the

bottom, taking care not to apply tension on any

internal wiring.

2. If applicable, remove and discard the black hole

plug on the sloped front panel above the “PRES-

SURE” text. This can be done by pinching the

clasps on the back of the plug from the inside of

the front plate.

3. Insert the PDM (2082E) through the panel cutout,

from outside in, making sure the rubber gasket

is on the outside of the controller front panel.

(If wires are preinstalled, remove the terminal

connector by releasing the tabs on the sides of

the module and gently pulling the terminal con-

nector off. Reference photos below.) Slide the

white mounting bracket onto the module with

the mounting screws pointing towards the front

panel. Slide the mounting bracket forward until

it touches the controller panel. The clasps on the

mounting bracket should align with the groves

on the module. Gently tighten the screws until

the module is held into place. (If removed, reat-

tach the terminal connector.)

Terminal Connector Removal

1 2 3 4 5 6 7 8

Inhaltsverzeichnis

Seite 1 - Pressure Display Module (PDM)

Installation Instructions for Pressure Display Module (PDM)556MMeter Installation in 4848 Reactor Controller1. Unplug the power cord of the 4848 cont

Seite 2 - PDM Installation

PDM InstallationParr Instrument Company2Meter Installation in 4848 Reactor Controller (Continued)Meter Installation Diagram

Seite 3

PDM Installationwww.parrinst.com37 8 9 10 11 121 2 3 4 5 62082E Pin Out(Pin 5 is blank)6. Take the black and white cable, with both ends stripped, fr

Seite 4

PDM InstallationParr Instrument Company4Wiring Installation in 4848 Reactor Controller (Continued)9. Find the free orange wire #1 from the kit and at

Seite 5

PDM Installationwww.parrinst.com5PDM Wiring Schematic2082E/1212STRIP .23BLACK#112082E/75-WHITE +STRIP .2319LOC1NO.WIRE4+BLUE13STRIP .35END#2LOCWHIT

Seite 6

PDM InstallationParr Instrument Company6A2104E Harness Wiring Schematic

Seite 7

PDM Installationwww.parrinst.com7Factory Default SettingsPressure ModuleKeys command:1. Press “SET” to select 2. Press return key move to next opera

Seite 8 - Revision 05/03/13

Revision 05/03/13

Weitere Dokumente für Sensoren Parr-instrument PDM

Um das Dokument anzuzeigen Parr-instrument PDM Bedienungsanleitung

Parr-instrument PDM Bedienungsanleitung (12 Seiten)

Kommentare zu diesen Handbüchern

Keine Kommentare

Parr-instrument PDM Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Sensoren Parr-instrument PDM herunter. Parr Instrument PDM User Manual Benutzerhandbuch

Inhaltsverzeichnis

Weitere Dokumente für Sensoren Parr-instrument PDM

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sensoren Parr-instrument PDM